2008 NOVICE PURE STOCK RULES

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAR:

 

 

 

 

 

 

 

 

 

 

1)

American made RWD, front engine car or truck, 108" minimum wheelbase

 

 

 

 

 

 

 

 

 

 

 

 

ENGINE:

 

 

 

 

 

 

 

 

 

 

1)

Must have V-8 engine, OEM size and configuration

 

 

 

 

 

2)

Stock engine location, no moving motor back or down

 

 

 

 

3)

same brand as car, Gm to GM, Ford to Ford, etc.

 

 

 

 

 

4)

Stock motor mounts in stock locations only.

 

 

 

 

 

5)

Flat Top Pistons only. STOCK COMPRESSION MOTORS ONLY

 

 

 

 

6)

No Performance parts of any kind allowed (STOCK ONLY)

 

 

 

 

7)

Cast iron OEM heads only, no Vortec Heads, no other heads allowed

 

 

 

 

No Porting, polishing, milling or altering of any kind

 

 

 

 

 

8)

Cast iron exhaust manifolds only no Ram Horn type exhaust allowed.

 

 

 

 

No center dump or LT1 type exhaust

 

 

 

 

 

 

9)

Cast Iron OEM Quadrajet or 2 barrel intakes only , no aluminum intakes

 

 

 

 

No Marine or Bowtie Intakes allowed.

 

 

 

 

 

 

10)

No Aftermarket power steering pump allowed.

 

 

 

 

 

11)

No Aluminum pulleys allowed.

 

 

 

 

 

 

12)

 Aluminum Radiators Allowed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CARBURETOR:

 

 

 

 

 

 

 

 

 

1)

OEM Carb only.

 

 

 

 

 

 

 

2)

No modification of carburetor

 

 

 

 

 

 

3)    

No Aftermarket or Performance Carbs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IGNITION:

 

 

 

 

 

 

 

 

 

 

1)

OEM HEI or OEM point distributor only with one 12 volt coil

 

 

 

 

 

 

 

 

 

 

 

TRANSMISSIONS:

 

 

 

 

 

 

 

 

1)

OEM automatic transmission only

 

 

 

 

 

 

2)

All gears must work

 

 

 

 

 

 

 

3)

Must have 1 ½" inspection hole on bottom of bell housing

 

 

 

 

4)

Must have working stock torque converter

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DRIVE SHAFT:

 

 

 

 

 

 

 

 

 

1)

Must be painted white with loop within 1 foot of transmission

 

 

 

 

2)

Must be steel, OEM drive shaft only

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REAR END:

 

 

 

 

 

 

 

 

 

 

1)

OEM original type rear end in stock location

 

 

 

 

2)

Must match make of car.. No 9” Ford in Chevy

 

 

 

 

 

3)

Gears may be locked, no limited slip, no spools, weld only

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BODY:

 

 

 

 

 

 

 

 

 

 

1)

No gutting of any kind except to allow for door bars,

 

 

 

 

 

resonable tire clearance, and under fuel cell for fuel escape.

 

 

 

 

2)

Plastic Nose Piece Ok

 

 

 

 

 

 

 

3)

No Wedge Noses

 

 

 

 

 

 

 

4)

No Spoilers or wings allowed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIRES & WHEELS:

 

 

 

 

 

 

 

 

1)

Asphalt take offs only

 

 

 

 

 

 

 

2)

Grooving OK

 

 

 

 

 

 

 

3)

10" maximum steel wheel with minimum 1" OD lug nuts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DRIVERS AREA:

 

 

 

 

 

 

 

 

 

1)

Must have a 5 or 6 point safety harness, must be bolted to frame or roll cage

 

 

 

2)

Safety harness must be no more than 2 years old

 

 

 

 

 

3)

Steering column in stock location

 

 

 

 

 

 

4)

Quick release steering wheel OK, No quick steering reducers

 

 

 

 

5)

3 vertical bars installed infront of driver minimum 3/8 diameter

 

 

 

 

6)

Stock brack master cylinder only with cylinder and pedal in stock location

 

 

 

7)

Firewall and floor pan must remain original and all holes must be covered

 

 

 

 

 

 

 

 

 

 

 

 

BATTERY:

 

 

 

 

 

 

 

 

 

 

1)

May be moved and must be securely mounted

 

 

 

 

 

2)

If in driver's compartment, must be totally encased.